Digital Oscilloscope Kit,Aideepen Handheld oscilloscopes with DC/AC Power Supply and BNC-Clip Cable Probe

Digital Oscilloscope Kit,Aideepen Handheld oscilloscopes with DC/AC Power Supply and BNC-Clip Cable Probe

Digital Oscilloscope Kit,Aideepen Handheld oscilloscopes with DC/AC Power Supply and BNC-Clip Cable Probe Function: 5mV/div - 20V/div high Sensitivity,With Auto/Normal/ Single trigger model,added the rotary encoder, makes parameter adjustment quicker and easier.You also can conduct secondary development , for example, it can be changed to Millivoltmeter, data loggers.This handheld oscilloscopes is a complete finished product, without welding,easy to operate and carry,very suitable for your electronic project.2.4-inch TFT Clearly display the test results, and can freeze/save waveform display content at any time.(including frequency, period, duty ratio etc.)We added a 9V battery buckle, you just need to connect the 9V battery use it at outdoor. Note: Please check user guide to get more help. We greatly appreciate your POSITIVE feedback. Please do not leave negative feedback without asking for help. If you have any questions , please let me know ! we will try our best to solve any problem.Thank you very much! Package 1 Oscilloscope 1 BNC-clip cable 1 Users Manual 1 AC Power Adapter 1DC 9V battery buckle Specifications: Sensitivity Range: 5mV/div-20mV/idv Analog Bandwidth: 0-200KHz Maximum Real-time Sampling Rate: 1MSa/s Maximum Input Voltage: 50Vpk (1X probe) Input Impedance: 1M ohms/20pF Accuracy: 12 Bits Record Length: 1024 points Coupling Modes: DC / AC / GND Time Base Range: 500s/Div - 10us / Div Trigger Modes: Auto, Normal, and Single Supply Voltage: DC 9V(8-10V) Current Consumption:~120mA 9V Size: 1027423mm/42.90.9 inch Read more Q&A: Q1:Why need to trigger? A1:When the oscilloscope is not triggered, the signal (automatic mode) will be randomly grabbed and generate an image. Since the signal is continuous, the waveform randomly is not regular.After trigger, you can get regular waveforms to analyze research. Q2:How many trigger modes have this oscilloscope? A2:Our oscilloscope has 3 trigger mode,With the Auto / Normal / Single Trigger mode, you can easily capture the current waveform. Q3:trigger level not center trigger level A3: Hold down [TRIGGER] button for about 3 seconds. This will set the trigger level to the medium value of signal amplitude. Q4:Display white screen. A4: Power supply voltage must be in the range of 8 - 10V;Confirm signal input within range of equipment parameters;Default Restore. Q5:Why does the encoder knob rotate trigger level up and down without change? A5: The encoder knob of the equipment needs to be fine-tuned in design, so it needs to be adjusted slowly to work. When the speed is too fast, the device will be considered invalid. Q6: Why my voltage numbers are incorrect? A6: There are two possible causes for wrong voltage display. 1 ) The reference point has not been calibrated(you just need to perform VPos alignment as instructed in the manual (it is strongly suggested to do factory default restore before VPos alignment to make sure all parameters are valid) 2 ) the gain of analog channel is incorrect. (you just need to perform VPos alignment as instructed in the manual (it is strongly suggested to do factory default restore before VPos alignment to make sure all parameters are valid). please refer the Troubleshooting section in the manual to find possible reasons in the analog channels. For any other question, welcome to ask anytime. FOR DIY You can do secondary development on this kit.For example, it can be changed to millivolt meter, data loggers. Encoder Added the encoder, Make adjustment quicker and easier. Portable Mini handheld oscilloscope, less than 100g,Suitable for outdoor work. Read more Digital Oscilloscope Kit Atmega328 Transistor Tester TC-T7 Transistor Tester TC-T7-H Transistor Tester LCR-TC1 Multi-Function Capacitance Resistance ESR Tester Mode Oscilloscope Transistor Tester Transistor Tester Transistor Tester Transistor Tester

Product Features

• EasyThis handheld oscilloscopes is a complete finished product, without welding,easy to operate and carry,very suitable for your electronic project.
• AddedWe added a 9V battery buckle, you just need to connect the 9V battery use it at outdoor.
• Clearly display2.4-inch TFT Clearly display the test results, and can freeze/save waveform display content at any time.(including frequency, period, duty ratio etc.)
• Function5mV/div - 20V/div high Sensitivity,With Auto/Normal/ Single trigger model,added the rotary encoder, makes parameter adjustment quicker and easier.You also can conduct secondary development , for example, it can be changed to Millivoltmeter, data loggers.
• Package1* Oscilloscope,1* BNC-clip cable,1*User Guide,1*AC Power Adapter,1*9V battery buckle(NOT Included 9V battery).Pls contact us if have any quality issue and need support, will reply within 24hours.

Tags:dingo

Title - Default Title