ETEPON Digital Oscilloscope Kit with BNC-Clip Cable Probe with Power Supply, (Assembled Finished Machine) EM001
ETEPON Digital Oscilloscope Kit 2.4” TFT Adapter Added Version Thanks for some customers' advice, we have updated this oscilloscope and added a suitable adapter for it. Package： 1 Oscilloscope 1 BNC-clip cable 1 Users Manual 1 A Power Adapter Advanced Features No need do assembly or soldering work Easily Measuring Professional Assembly Detailed Instruction Sensitivity Extended Handheld Rotary Encoder Added Read more ETEPON Digital Oscilloscope Kit Kindly Note This oscilloscope runs on 9V power adapter. The power supply voltage must not exceed 10V. Otherwise it is possible to burn out the machine. 9v dc power supply should be center positive.Resistor values can easily be misinterpreted. It is highly recommended to check their values via an ohmmeter before soldering them to the board.Make sure you know the polarity and orientation of all parts. Read more Sensitivity Extended The sensitivity of the EM001 has been extended both in width and height, which is wider and wider than the others. It reaches 5mV / div - 20V / div, while others is only 10mV / div - 5v / div. Rofessional Assembled Display and MCU are mounted on the same board (mainboard) to avoid using inter-board pin-headers. Analog channel is placed on a separated board which contains most user install parts, so the analog and digital circuits can be better separated. Rotary Encoder It has been added the rotary encoder, makes parameter adjustment quicker and easier. Read more Hand-Held This updated digital oscilloscope can be hand- held, while the others can only be used by placing it on the desktop. Measuring Easily Using the Auto/Normal/Single Trigger mode,it is easy to capture instantaneous waveform. Hold Function You can freeze waveform display at any time.And with waveform storage function you will not lose the waveform after power off. Read more Specification Number of Channel 1 Analog Bandwidth 0 - 200KHz Sensitivity 5mV/Div - 20V/Div Sensitivity Error < 5% Resolution 12-bit Input Impedance 1M ohm Maximum Input voltage 50Vpk Coupling DC, AC, GND Trigger Modes Auto, Normal, Single Trigger Types Rising/falling edge Trigger Position 1/2 of buffer size fixed Display 2.4 inch color TFT LCD with 320 x 240 resolution Power Supply 9V DC (8 - 10V acceptable) Dimension 115mm X 75mm X 22mm Weight 100 gram Answers for Frequently Asked Questions to help you: Q1, Display white screen? A1: Power supply voltage must be in the range of 8 - 10V.； Confirm signal input within range of equipment parameters. Q2,trigger level not center trigger level? A2: Hold down [TRIGGER] button for about 3 seconds. This will set the trigger level to the medium value of signal amplitude. Q3: Why my voltage numbers are incorrect? A3: There are two possible causes for wrong voltage display. 1 ) The reference point has not been calibrated, and 2 ) the gain of analog channel is incorrect. For 1 ) you just need to perform VPos alignment as instructed in the manual (it is strongly suggested to do factory default restore before VPos alignment to make sure all parameters are valid). For 2 ) please refer to the Troubleshooting section below to find out possible causes in analog channel. Q4: Can I use DSO Shell to measure high voltages like AC 220V ? A4: This oscilloscope was designed for low voltage measurement. The maximum input voltage was specified as 50Vpk (peak value). So it can not be used to directly measure any voltage higher than 50V. Otherwise that could damage the device or even cause body injury. But if attenuator is used it is possible to use oscilloscope to measure voltages higher than 50V. Using a standard probe at 10X setting, for example, it can take voltage up to 400V. However users need to fully understand the potential risk before doing so and will do at his/her own risk. strongly discourages users to use it for measurements at voltages higher than specified. Seller will assume no responsibility for any damages, losses, or body injuries caused by using DSO Shell to measure voltages higher than specification. Q5: Why does the encoder knob rotate trigger level up and down without change? A5: The encoder knob of the equipment needs to be fine-tuned in design, so it needs to be adjusted slowly to work. When the speed is too fast, the device will be considered invalid. If you have any question on using this oscilloscope, please feel free to contact with us!
Product Features
- SIMPLE DESIGNETEPOPN EM001 oscilloscope kit is an assembled finished machine that can be used directly to avoid assembly/soldering process problems and saving you a lot of time. The display and MCU are mounted on the same board (motherboard) to avoid the use of inter-board pinouts. The analog channels are placed on a separate board containing most user-installed parts, thus allowing better separation of analog and digital circuits.
- UPGRADED VERSIONThe sensitivity of the EM001 oscilloscopes has been extended both in width and height which is wider and higher than the others It reaches 5mV / div - 20V / div while the others is only 10mV / div - 5v / div.
- HAND-HELDThis updated digital oscilloscope can be hand-held while the others can only be used by placing it on the desktop.
- ROTARY ENCODERIt has been added the rotary encoder makes parameter adjustment more quicker and easier.
- WHAT YOU GETYou will get an assembled mini oscilloscope, BNC clip cable, and a power supply. Detailed operating instructions (troubleshooting guide) and schematics are also provided. If you have any questions about this digital oscilloscope, you can always contact us and we will reply within 24 hours.
Tags:dingo
Title - Default Title