hygger Aquarium Alarm Auto Top Off Kit, Fish Tank Smart ATO Water Pump Auto Refill Water and One-Key Drain Water, Water Level Monitor Two Pairs of Protection Sensors for Saltwater Freshwater Tank
Read more SAFETY: Light Flashs and Beeping Alarm Connect the water pump cord Working State: Constant brightness when refilling water; Off when standby.Display Abnormal: Beep and Blue light flashingStop Working: 1.The refill water pump in the reserve water tank is out of water; 2.The refilling pump’s electric wire loose; 3.The water pump is working abnormally.Trouble Shooting: 1.Place the pump into the water then press the M button; 2.Plug the water pump into the monitor Blue light hole tightly; 3.Change the pump. Connect the external optical sensor cord Working State: Green Light OffDisplay Abnormal: Beep and Green light flashingStop Working: 1.Water shortage in reserve water tank; 2. External sensor’s electric wire loose; 3.The external sensor is working abnormally.Trouble shooting: 1.Refill water into the reserve water tank, make sure the reserve water is higher than external sensor; 2.Plug the sensor into the monitor Green light hole tightly; Connect the power adapter cord Working State: Red Constant brightnessDisplay Abnormal: RED Light OFFTrouble Shooting: 1.Make sure the power adaptor is plugged into the monitor Red light hole tightly; 2.Confirm that the power supply. Display Abnormal: All lights flashing and BeepStop Working: 1. Calibration is not stable; 2. The water level in the tank is higher than the ATO.Trouble Shooting: 1. Remove the external monitor and set it down horizontally. Let it re-calibrate precisely; 2. Wipe the monitor and the fish tank wall. Connect the water pump cord Working State: Constant brightness when draining water, Off when standby.Display Abnormal: Beep and Yellow light flashingStop Working: 1. The fish tank where has drain pump is out of water; 2. The water pump’s electric wire loose; 3. The water pump is working abnormally.Trouble shooting: 1. Place the pump into the water then press the M button; 2. Plug the drain water pump into the monitor Yellow light hole tightly; 3. Change the pump. Read more HOW TO INSTALL THE MONITOR In order to make the product monitoring more accurate and avoid errors, please clean the fish tank wall where the monitor is placed and the two sides where the monitor is fixed on the fish tank wall during the first use. And it is recommended to clean regularly. Put the monitor into the tank and outside the tank respectively, move them horizontally until they are overlapped, and never overlap the inner and outer parts directly. Because the magnetic force in hygger product is very strong. Make sure that there are no obvious bubbles in the fish tank water near where the monitor is placed. It will affect the judgment of the sensor and cause incorrect or non-refilling of water. When the water level line is near A (the first monitoring probe), the product will automatically refill water;When the water level reaches B (the second monitoring probe), the automatic refill will be suspended;Our product uses an ultra-wide prism, and point C will always be kept clean. When the point below B is covered with impurities such as green algae for a long time, the monitoring fails and overflows, but C is not affected, and an alarm will sound. Read more HOW TO INSTALL THE UNIVERSAL HOLDER Put the holder on the wall of the fish tank; Tighten the screws to fix; Align the clip with the protruding slide, and install the hose clip; Insert the hose; Install the last hose clamp. Read more TIPS If the external sensor is placed in a spare water tank with glass, please slide the installation horizontally. The thickness of the glass wall of the fish tank is recommended to be ≤0.15in. If you are using a bucket and the thickness is very thick, you can put all the external sensors in the bucket instead of placing them separately. The small black button is to prevent water from entering the hole, so please save it when not in use. DC 12V 5WH.max:6.5FTQ.max:74 GPHLine length:70in Read more INSTALL CORRECTLY (Place the monitor horizontally) NO: Three holes face up NO: Put vertically NO: Put oblique Read more
Product Features
- SOUND ALARM: New security technology, two optical sensors monitor the water levels, double protection, can attract your attention quickly. When it occurs below situations, it will make a loud beeping noise to warn you: 1 The water pump that placed in the bucket is out of water. 2Water pump's electric wire loose. 3External sensor is out of water. 4Fish tank water level is higher than the auto top off monitor pump.
- LED INDICATORS ALARM: The red light is constant brightness, which means it is working normally,off is not ok. If other lights flash, it indicates that there is an issue with the device, which needs to be checked and corrected with reference to the manual. YELLOW LIGHT: water pump drain water; BLUE LIGHT: water pump refill water; GREEN LIGHT: external optical sensor; RED LIGHT:power adapter.
- DOUBLE APPLICATION: Auto refill and one-key drain water. Put the water pump in the fish tank, and plug the water pump cord into the upper(Yellow light hole) to drain water. On the contrary, put the water pump into the reserve water tank and plug in Blue light hole for auto refill water, and plug in external optical sensor to avoid water shortage in the reserve water. M button, PAUSE/CHANGE WORKING MODE.
- SIMPLE TO USE: Easy to install and use, no complicated programs. Connect water pump, external sensor and power supply to monitor and its ready to run. Suitable for saltwater and freshwater tanks(up to 60 gals). Can be installed in a cabinet filter or directly on the aquarium edge. Because of monitoring, no longer have to worry about the lack of water in the spare water tank placed in a hidden location.
- QUALITY MATERIAL: ATO MONITOR * 1,super strong magnetic, firmly fixed on the wall of the fish tank (12mm). WATER PUMP * 1, DC 12V 5W, H.max:6.5FT, Q.max:74 GPH. HOSE * 1; EXTERNAL OPTICAL SENSOR * 1,widen the edge, the monitoring is more precise. POWER ADAPTER * 1,DC 12V 1A. UNIVERSAL HOLDER *1, for 3/4 inch thickness tank, hose holder. USER MANUAL *1.
Tags:paw07
Title - Default Title