XIM V13H010L67 ELPLP67 Replacement Projector Lamp Compatible with Epson EB-W12 EB-X12 EB-S12 EX5210 EX6210 EX7210 H428A H429A H430A HC710UG MG-50
Projector Lamp Type: Projector lamp with Housing Model number: ELPLP67 Compatible with Projector models: Epson EB-S02 EB-S022 EB-S11 EB-S12 EB-SXW11 EB-SXW12 EB-W02 EB-W12 EB-W16 EB-W16SK EB-X02 EB-X11 EB-X12 EB-X14 EB-X15 EH-TW480 EH-TW510 EH-TW550 EX3210 EX3212 EX5210 EX6210 EX7210 H428A H429A H430A H431A H432A H433A H435B H435C H436A H444C H493C H494C H499C H518A HC710UG MG-50 MG-850HD Powerlite 1221 Powerlite 1261W Powerlite 710HD Powerlite HC 500 Powerlite HC 707 Powerlite HC 710HD Powerlite HC 750HD Powerlite Home Cinema 710HD Powerlite S11 Powerlite W16 Powerlite W16SK Powerlite X12 Powerlite X14+ Powerlite X15 Read more Step 1. Unplug the power cord from your projector and let the lamp cool down. Step 2. Locate the lamp access panel on your projector and remove the screws and access panel. Step 3. Remove any screws holding the lamp housing into the projector. Step 4. Reach in and firmly pull the lamp housing out of the projector. Step 5. Place the new lamp housing into the projector in the same orientation as you removed the old lamp. Step 6. Wiggle the lamp into place and make sure full contact is made inside of the projector. Step 7. Replace the lamp mounting screws to secure the lamp into the projector. Step 8. Replace the lamp access panel and secure the screws. Step 9. Plug in your projector and power it on. Step 10. Reset the lamp counter. Some lamps will reset the lamp counter automatically when a new lamp is placed in. Read more Where is My Projector Lamp Located A projector lamp can be found by locating a square or rectangular plastic plate somewhere on the outside of the projector; the plate is usually on the bottom of the projector, but can sometimes be found on the top or sides. This cover is usually secured by two screws; undo these screws and lift the plate off to reveal the bottom of the plastic housing (the module) that holds the projector lamp in place in your projector. This plastic housing usually has a handle attached to it. Pull gently on this handle to remove the projector lamp from your projector. It is time to replace the lamp when: Picture has become dull and lacks brightness. There is an obvious decline in picture clarity and sharpness. Your lamp is flickering. There is difficulty or a delay when turning the machine on. A light comes on that warns you that it may be time to change your lamp. Note: 1. Let the lamp cool down before replacing it. If the lamp breaks, handle the shards carefully to avoid injury. 2. Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 3. Be sure to seat the lamp fully and secure the lamp cover. If the lamp is not properly installed or the cover is loose, the lamp will not turn on. Read more
Product Features
- XIM Lamps Compatible with Epson EB-S02 EB-S022 EB-S11 EB-S12 EB-SXW11 EB-SXW12 EB-W02 EB-W12 EB-W16 EB-W16SK EB-X02 EB-X11 EB-X12 EB-X14 EB-X15 EH-TW480 EH-TW510 EH-TW550
- Brand new lamp with new housing. It is NOT just the bare lamp or bare bulb.
- All lamps are produced by our own factory
- All lamps are tested at the manufacturer before leaving the facility
- We can make a better offer for bulk order
Tags:cocoon
Title - Default Title